HB10: Bluetooth / RF handset control for dual actuator systems
Controls

HB10 wireless

The HB10 is a wireless handset control for TWINDRIVE dual actuators in leisure furniture. Comes in RF and Bluetooth editions. Ergonomic and user-friendly.

Product description

HB10 wireless

The HB10 wireless handset is designed for use with leisure beds with TWINDRIVE® radio frequency-based (RF) systems or Bluetooth® connection.

The HB10 wireless handset combines ergonomic design and functionality into a user-friendly handset with big intuitive buttons and without any annoying cables.

Product data sheet

HB10 Wireless data sheet

View the data sheet as an online magazine or download the PDF.

TWINDRIVE TD4 Advanced user manual

This user manual will tell you how to install, use and maintain your LINAK TWINDRIVE products.

TWINDRIVE TD4 Standard user manual

This user manual will tell you how to install, use and maintain your LINAK TWINDRIVE products.

TWINDRIVE® TD5 Standard user manual

This user manual will tell you how to install, use, and maintain your LINAK® TWINDRIVE® products.

TWINDRIVE TD1 220/250 user manual

This user manual will tell you how to install, use, and maintain your LINAK TWINDRIVE products.

HOMELINE product overview

Explore the variety of TWINDRIVE systems with low noise level and small built-in dimensions used in both box spring beds and slatted beds.

TD4 quick guide - Pairing devices and mechanical lowering

Learn how it only takes a few steps to pair devices to the dual actuator TD4 using Bluetooth® technology or mechanically lower a comfort bed with TD4 in case of power shortages.

Support

The display shows 'E01' error code instead of the height.

The desk cannot be raised if it has not been initialised.

If the display shows error code 'E01', the desk has not been initialised.

How to initialise your desk:

  1. Press the down key until the desk is lowered completely. Hold the key until the desk no longer moves.
  2. Reactivate the down key and hold until the desk no longer moves. Now the desk can be raised.

DP1C and DPT - Height in the display is incorrect

Change the height in the display to the correct height of the desk by following the procedure shown in the video or described below.

How to set the height of your desk (DP1C and DPT)

Measure the height of your desk from floor to the upper edge of the desktop.

  1. Press and hold the ‘S’ button until an ‘S’ appears in the display.
  2. While pushing the ‘S’ button, use the up and down key to change the figure to the correct height.

DPF1C - Height in the display is incorrect

Change the height in the display to the correct height of the desk by following the procedure shown in the video or the instructions below.

How to set the height of your desk

Measure the height of your desk from floor to the upper edge of the desktop.

Set the height of your desk

  1. Press the up and down keys at the same time.
  2. A figure should appear in the display.
  3. Use the up or down key to change the figure to the correct height.

How to initialise your desk

The desk cannot be raised if it has not been initialised.

If error code 'E01' is shown in the display, the desk must be initialised.

How to initialise your desk:

  1. Press the down key until the desk is lowered completely. Hold the key until the desk no longer moves.
  2. Reactivate the down key and hold until the desk no longer moves.

Now the desk can be raised.

How to store a memory position

Favourite positions for sitting and/or standing can be stored. Follow the procedure shown in the video or the instructions below.

How to store a position

  1. Set the desk to the height you wish to store
  2. Press ‘S’ and then the memory button.

The position has now been stored.

To move your desk to the stored height, press the memory button until it reaches the stored position.

Desk cannot be raised full stroke. Always stops in same position.

The system has set a new end-stop outwards.

To reset a saved position, the desk must be re-initialised. Follow the procedure shown in the video.

The display only shows a dash (-) and does not work

The DPT is locked when not used to avoid unintended movement.

To unlock the DPT follow the procedure shown in the video.

Desk Panel DPT - The display shows ‘E01’ error code instead of the height

The desk cannot be raised if it has not been initialised.

If the display shows error code 'E01', the desk has not been initialised.

How to initialise your desk:

  1. Press the down key until the desk is lowered completely. Hold the key until the desk no longer moves.
  2. Reactivate the down key and hold until the desk no longer moves. Now the desk can be raised.

Got a question about electric actuator technology?

- We are not oracles. But, we are experts in actuator technology. So, feel free to ask us anything you like about that.

Subscribe to LINAK news

Stay informed about how actuator technology follows the megatrends of today and meets the global challenges of tomorrow.